Search found 532 matches

by Werner Van Loock
Fri Feb 20, 2009 2:25 pm
Forum: What doesn't fit anywhere else
Topic: Kit car scene
Replies: 2
Views: 3230

Re: Kit car scene

Don't know if they will be the first to be shelved. The way money can perish nowadays (banks going tits up) people tend to spend they're money instead.

Result in the dutch kitcarclub 4 GD T70's are ordered :shock:

and that aint the cheap side of the kitcarmarket
by Werner Van Loock
Tue Feb 17, 2009 12:58 pm
Forum: Parts for sale
Topic: Stylus fuel tank & Race battery.
Replies: 3
Views: 4544

Re: Stylus fuel tank

Is the tank modified for injection pump or not?

I might of messed up my tank modifying it to have a pickup with the cup at the bottom wich you and Matt have now.
by Werner Van Loock
Mon Feb 16, 2009 6:09 pm
Forum: Parts for sale
Topic: A couple of bits
Replies: 4
Views: 4491

Re: A couple of bits

what is a petty strut and where does it go? A forward facing bar that attaches to the mid point of the main roll hoop & attaches diagonally into the corner of the passenger footwell (or similar). Like wot I've got in mine :D Wasn't very passenger friendly was it Werner ?? Not needed if you've got a...
by Werner Van Loock
Mon Feb 16, 2009 10:18 am
Forum: SVA, MOT, etc...
Topic: seatbelt attachments
Replies: 11
Views: 8875

Re: seatbelt attachments

Don't run the seatbelts through the seatbelt holes in your seats for SVA, because they need a certification then to prove they can withstand certain forces in case of a collision. especially if the seatbelts touch the holes when you're strapped in! Just run them round the seats for SVA. Also make su...
by Werner Van Loock
Thu Jan 29, 2009 11:16 pm
Forum: Engines, gearboxes, differentials, brakes, etc...
Topic: Manifold
Replies: 20
Views: 11873

Re: Manifold

20V engine is a very nice one to have in a road car, but not very good at racing. when funds allow, i'll be building a 16v with 7rib block with the strong balanced bottom end using steel conrods and forged high compression pocketed pistons, high pressure oil pump and a flowed smallport head with som...
by Werner Van Loock
Thu Jan 29, 2009 9:48 pm
Forum: Engines, gearboxes, differentials, brakes, etc...
Topic: Manifold
Replies: 20
Views: 11873

Re: Manifold

I know it are Dellorto DHLA carbs, but that's about it. But everything depends on the engine. Mine is a 7 rib block with 20mm gudgeon piston cooling conrods/42mm conrod big end, small port high 10.3 compression head. While most are 3 rib block 18mm gudgeon non piston cooling conrods/40mm conrod big ...
by Werner Van Loock
Wed Jan 28, 2009 11:02 pm
Forum: Engines, gearboxes, differentials, brakes, etc...
Topic: Manifold
Replies: 20
Views: 11873

Re: Manifold

here it is, don't think that even with a cut and shut it would fit

measurements are in cm, don't use any imperial measurements here 8)
front view
front view
overview
overview
top measurement in cm (1inch = 2,54cm)
top measurement in cm (1inch = 2,54cm)
height measurement in cm
height measurement in cm
by Werner Van Loock
Wed Jan 28, 2009 10:39 pm
Forum: Engines, gearboxes, differentials, brakes, etc...
Topic: Manifold
Replies: 20
Views: 11873

Re: Manifold

I'll check in the garage on the striker, it has a Raw 4age exhaust on it
by Werner Van Loock
Thu Jan 22, 2009 8:26 pm
Forum: (Re)Build progress & Mods
Topic: Todays Progress for me!
Replies: 15
Views: 12630

Re: Todays Progress for me!

Looking good, get your SVA application in ASAP, only few weeks left for applying, after that it's IVA
by Werner Van Loock
Sun Jan 18, 2009 10:21 pm
Forum: What doesn't fit anywhere else
Topic: Jeremy Phillips has done it again
Replies: 8
Views: 6438

Jeremy Phillips has done it again

Another Phoenix/Fury/Stylus spin-off

Spectre

Full bodied car based on the riot

Image
by Werner Van Loock
Wed Jan 14, 2009 8:59 pm
Forum: General Stylus related
Topic: stylus history
Replies: 11
Views: 8347

Re: stylus history

Regarding the axle in the RT - I thought the "atlas" axle was used to give the wider track (out of capris and many other donors)? Not so :wink: Some people chose to go this route but it was not a factory standard. If big power/torque is planned , it could be a good route but baby atlas axles are he...
by Werner Van Loock
Mon Jan 12, 2009 10:16 pm
Forum: What doesn't fit anywhere else
Topic: A daughter
Replies: 14
Views: 8348

Re: A daughter

It's a garage connected to the house, but no heating inside. Though the central heating burner is in there. In the next few weeks i need to connect 2 extra radiators to the system on the 2nd level and might connect a 3rd one in the garage at the same time, this should keep the extreme cold outside, ...
by Werner Van Loock
Mon Jan 12, 2009 3:38 pm
Forum: What doesn't fit anywhere else
Topic: A daughter
Replies: 14
Views: 8348

Re: A daughter

congratulations werner! Another car enthusiast maybe? :wink: Has to be, with 2 kitcars in the garage and a brother and sister that's more interested in cars then Barbies Congratulations, does that put car building on the back burner for a while again now? :cry: No way, first get the striker on the ...
by Werner Van Loock
Fri Jan 09, 2009 10:53 pm
Forum: What doesn't fit anywhere else
Topic: A daughter
Replies: 14
Views: 8348

A daughter

Allysia was born yesterday (8th)

Image

That's why i've been quiet lately
by Werner Van Loock
Tue Jan 06, 2009 10:19 pm
Forum: Parts for sale
Topic: spare chassis on the bay
Replies: 1
Views: 3018

spare chassis on the bay